From: Tadeusz Wysocki Jr. <tswysocki**At_Symbol_Here**GMAIL.COM>
Subject: Re: [DCHAS-L] polymer curing question
Date: Tue, 26 Feb 2019 08:43:07 -0500
Reply-To: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**PRINCETON.EDU>
Message-ID: CAB=pEV5d0xnZ3pteG4VpagM3sGLET8BEcmKv+AuQjCbQ_hw+_w**At_Symbol_Here**mail.gmail.com
In-Reply-To <2080533083.5275099.1551119041134**At_Symbol_Here**mail.yahoo.com>


Low flash point solvents are being used in the aircraft industry for urethane to metal bonding.
Same thing with uncured epoxy prepregs..
We used high flow ovens to keep below the Low Explosion Level ( LEL) for that solvent.
Safer alternatives to DMF are available,....NR-150 ( Dupont - AVIMID N ) ,.....diamine cured Polyimide solution ( 50% ) was produced in 3 different solvents. NMP, DMF and Ethanol.
Hope this helps,
Ted.


On Mon, Feb 25, 2019 at 2:03 PM Monona Rossol <0000030664c37427-dmarc-request**At_Symbol_Here**lists.princeton.edu> wrote:
And don't forget a TLV-TWA of 5 ppm.

Monona Rossol, ACTS NYC


-----Original Message-----
From: Ellen M. Sweet <ems325**At_Symbol_Here**CORNELL.EDU>
To: DCHAS-L <DCHAS-L**At_Symbol_Here**PRINCETON.EDU>
Sent: Mon, Feb 25, 2019 10:21 am
Subject: [DCHAS-L] polymer curing question

Hi everyone,
I have a question from one of our researchers here at Cornell. Here's the background:
"The process involves synthesizing and curing a novel polymer, PDMS based PU, onto plastic "coupons" which will have DFM evaporating off.
The cure process is intended to have the polymer form onto the surface of the coupons in a thin coat and make the surface non-binding."
Our question is how to do this safely? DMF has a flash point of 58 =B0C and a vapor density of 2.52.
A known method for this curing process is to place the plastic coupons into a flammable oven that is under vacuum and flushed with nitrogen.
Can anyone suggest another method that doesn't involve the use of an oven like this? The group would have to purchase one to the tune of $50,000!
Thanks, Ellen
Ellen Sweet
Laboratory Ventilation Specialist
Department of Environmental Health and Safety, Cornell University
American Chemical Society, Division of Chemical Health and Safety
315-730-8896
--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas
--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas
--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.