From: Michael Ahler <mahler**At_Symbol_Here**HANCOCKCOLLEGE.EDU>
Subject: Re: [DCHAS-L] Attaching a regulator with a washer...
Date: Thu, 10 Jan 2019 23:10:09 +0000
Reply-To: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**PRINCETON.EDU>
Message-ID: CY4PR11MB148082A045C1260C35128599B7840**At_Symbol_Here**CY4PR11MB1480.namprd11.prod.outlook.com
In-Reply-To


Margaret,

CO2  regulators have a flat flange seal between the nut and the tank, not a "bullet nose" metal-to-metal seal as many other gases do, so they need a "gasket"  (the washer) between the flanges to effect a seal.

Try this:     dab a little bit of glue stick to a couple of small spots on the washer and stick it to the inside of the nut.   One advantage is that if this proves undesirable, the glue stick can be washed off with water.

Your gas supplier might be able to provide you with a few extra washers for your CO2 tanks if you ask.   CO2 tanks are (were -  1993 last I did this) supposed to come with a fiber washer, but too often they get lost or forgotten.  Save the washers you do get to build up a small supply of them for when a tank comes in sans washer or you mysteriously lose one.

And many hardware stores have a "nut and bolt" department that will also offer  a wide range of mongrel washers - possibly including a close match to the fiber washers your CO2 tanks need.    Stay with fiber washers if you do this.   Rubber or plastic washers will stretch under the CO2 pressure inside the fitting (or cryogenically crack if you are dispensing liquid CO2)  and leak.


Good luck.

Michael Ahler


Michael Ahler
Associate Faculty Member
LPS (Chemistry)
Allan Hancock College

From: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**PRINCETON.EDU> on behalf of Margaret Rakas <mrakas**At_Symbol_Here**SMITH.EDU>
Sent: Thursday, January 10, 2019 2:04:55 PM
To: DCHAS-L**At_Symbol_Here**PRINCETON.EDU
Subject: [DCHAS-L] Attaching a regulator with a washer...
 
Hi,

I am looking for some practical advice (or maybe sympathy...)

We recently purchased a new regulator for CO2 tanks; this particular regulator has a washer and the accompanying manual says if the regulator comes with a washer, to use the washer.  I have attached regulators for more years than I care to count, but this is my first with a washer....

I was doing a training session for the end users and it turned out to be more of a physical comedy show, as the washer kept falling off/out of the coupling 'thingie'.  The tank is in a tricky space, but there is really nothing to hold the washer in place and the vendor's rep said using a bit of tape or other sticky material to tack it in place on the regulator side of the fitting was not OK.   We ended up not having the right attachment for an accessory so used the old setup.  Now we have the complete ensemble all set to go.

Does anyone have any 'tricks' or advice in how I can attach the regulator keeping the washer in place without looking like a complete klutz?
many thanks!
Margaret

--
Margaret A. Rakas, Ph.D.
Manager, Inventory & Regulatory Affairs
Clark Science Center
413-585-3877 (p)

--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.