From: "Demer, Frank R - (demer)" <demer**At_Symbol_Here**EMAIL.ARIZONA.EDU>
Subject: Re: [DCHAS-L] Haz Waste Transfer
Date: Fri, 27 Jun 2014 16:27:13 +0000
Reply-To: DCHAS-L <DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU>
Message-ID: 4A14EEF4B27C1A458D48A52027ED87F476BA26A7**At_Symbol_Here**Rivers.catnet.arizona.edu
In-Reply-To <4F21A5F3A002444D8B4F5E4B767431E5375EC9AD**At_Symbol_Here**EXMBX2010-7.campus.MCGILL.CA>


It sounds like we handle liquid hazardous waste in a similar manner.  We were handling 5-gallon liquid waste containers approximately 9 times through the disposal process with some lifts required a raised elbow and we were having wrist and shoulder CTDs.  Waste was transported in buildings and to a truck using a commercial plastic laundry bin cart.   We converted to 3.5-gallon waste containers; redesigned and custom-fabricated (from plastic) our waste carts with lower sides to reduce the lifting height, and accommodate two high stacks of six containers, added six appropriate casters (4 swivel casters on the corners, one locking, and two fixed casters in the middle) to allow the carts to easily move like tanks, and added a handle closer to elbow height, and starting using the lift gate on the truck.  Waste container handling was reduced to 3 times - once to put the container in the cart; the loaded cart was rolled onto the truck using the lift gate and locked in place using the locking caster; the loaded cart was taken off the truck in the same manner and the waste containers were taken out of the cart to store by compatibility before they were finally lifted to pour into 55-gallon drums.    We tried pumping the waste using a couple different methods, which were unsuccessful - mostly due to plugging from solids (pipette tips, etc.) that researchers would add to the liquids.     A mechanical lift assist device might work to reduce the ergonomic stressors from pouring but we have not tried this.

 

 

Frank R. Demer, MS, CIH, CSP

Health Safety Officer

Industrial Hygiene and Safety

University of Arizona

Department of Risk Management Services

 

Phone:  520.621.3585

Fax:  520.621.3706

Email:  demer**At_Symbol_Here**email.arizona.edu

Mailing Address:  P.O. Box 210300, Tucson, AZ  85721-0300

Street Address:  220 W. 6th St., Tucson, AZ 85701 (2nd floor, East Bldg.)

Web Address: http://risk.arizona.edu/

 

 

From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU]On Behalf Of Wayne Wood
Sent: Thursday, June 26, 2014 12:48 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Haz Waste Transfer

 

We installed a compressed air system to transfer our solvent waste from 5 gallon containers into our bulk containers. The system is far better ergonomically than manual handling and the investment has paid for itself many times over.

 

W.

 

Wayne Wood | Associate Director, University Safety (EHS), University Services -Directeur Adjoint, Direction de la pre´vention (SSE), Services universitaires |McGill University | 3610 rue McTavish Street, 4th floor | Montreal, Quebec, Canada, H3A 1Y2 | Tel: (514) 398-2391

 

 

 

 

From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU]On Behalf Of Heidi Dixon-White
Sent: Thursday, June 26, 2014 3:19 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: [DCHAS-L] Haz Waste Transfer

 

We routinely collect liquid hazardous waste in 5-gall containers in our laboratories.  This waste stream primarily consists of flammable solvents and water.  Full containers are moved to our bulk haz waste accumulation room and transferred to 55 gall drums.  The 5-gall containers are very heavy so lifting/pouring can easily lead to spills.  We have found that hand pumps also tend to be messy.  Does anyone use a mechanical pump (intrinsically safe, possibly air driven, or other) to manage this type of transfer? 

 

 

 

Heidi Dixon-White
Chemical Hygiene Officer & Safety Coordinator

dixonwhiteh**At_Symbol_Here**abclabs.com

www.abclabs.com

573.777.6146

317.796.4282

              

 


This message including any attachments may contain trade secrets and other confidential information and may be disclosed or used only by the intended recipient(s). If you have received this message in error, please delete it and notify the sender immediately. Unless you are the intended recipient, you are not authorized to and should not read, retain, copy, or disseminate this message.


Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.