All,
We have operations where we only need to protect the product being tested and not the worker, mostly procedures where we are looking for very low levels of non-hazardous particulates on the surfaces of pharmaceutical containers. Although we call the laminar flow units we use for these procedures clean benches, not hoods.
But we also have a hood we purchased from Air Control (Microvoid) that is used for ICP prep where we are looking for very low levels of metal ions. It has both a laminar flow through a HEPA filter to protect the product/testing and also draws air into it, like a standard hood, to protect the worker. It is constructed entirely of a polymer – no metal whatsoever. We purchased it because our scientists felt that they were getting contamination from our regular hoods in their work. It seems to alarm quicker than a regular fume hood… there is a lot more going on with the air flow… and it is also more challenging to do the annual PQ on it, we have to call in an expert.
Pat Peifer
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU]
On Behalf Of Monona Rossol
Sent: Friday, November 08, 2013 12:47 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] laminar flow hood purchase
For someone in my end of the biz where all our air contaminants have hazards, that was hard to comprehend. I hope we really have exposure data and know for sure that besides being non-infectious, these DNA/RNA thingies also do not provoke allergies or have any other hazards.
Monona
-----Original Message-----
From: Margaret Rakas <mrakas**At_Symbol_Here**SMITH.EDU>
To: DCHAS-L <DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU>
Sent: Fri, Nov 8, 2013 12:35 pm
Subject: Re: [DCHAS-L] laminar flow hood purchase
Monona--think PCR with non-infectious DNA/RNA (RG1). Or tissue culture with non-mammalian cells.....
best,
Margaret
On Fri, Nov 8, 2013 at 12:17 PM, Monona Rossol <actsnyc**At_Symbol_Here**cs.com> wrote:
I'm confused: On the first page of the link it says:
These vertical laminar flow Hoods are ideal for applications which are not hazardous to the operator but require a clean work area.
Monona Rossol, M.S., M.F.A., Industrial Hygienist
President: Arts, Crafts & Theater Safety, Inc.
Safety Officer: Local USA829, IATSE
181 Thompson St., #23
New York, NY 10012 212-777-0062
-----Original Message-----
From: Mark Lee <mleesafety**At_Symbol_Here**YAHOO..COM>
To: DCHAS-L <DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU>
Sent: Thu, Nov 7, 2013 11:39 am
Subject: Re: [DCHAS-L] laminar flow hood purchase
Shelly,
From what I have seen, the Laminar Flow Hoods are one of the best on the
market. Performing Lockout/Tagout audits, I see a lot of the bench top vertical
models. Here is a link for your viewing.
www.laboratory-supply.net/laminarflowhoods/shop_vertical_laminar_flow_hood_4feet.html?gclid=CI2kq_eL07oCFTJp7Aodsz4AAA
I hope this helps you out.
Respectfully,
Mark C. Lee
Safety Manager Specialist
Lockout/Tagout Specialist
> On Nov 7, 2013, at 10:11 AM, "Bradley, Shelly" <Bradley**At_Symbol_Here**HENDRIX.EDU> wrote:
>
> One of my faculty is interested in a laminar flow hood. I know nothing about
them.
> What do I need to know?
> Are the self-contained ones any good?
> Which brands are best?
>
> Thanks for your help!!
>
> Shelly Bradley
> NRCC-CHO
> Authorized OSHA Trainer
> Instrumentation Specialist
> Laboratory Development Assistant
> Campus Chemical Compliance Director
> Department of Chemistry
> Hendrix College
> Conway, AR 72032
> Ph: (501) 450-3812
> Fax: (501) 450-3829
> bradley**At_Symbol_Here**hendrix.edu
--
Margaret A. Rakas, Ph.D.
Manager, Inventory & Regulatory Affairs
Clark Science Center
413-585-3877 (p)
Previous post | Top of Page | Next post